The Jeffrey Prototype version 2.0

Published by Joey Joe Joe Jr on

Th

I’m giving away an iSpindel on February 5th, 2020 to celebrate The Jeffrey printed circuit board. Watch the video for details. Use this referral link to create an account, get a $5 discount, and help out my project.

Most of the detail is in the video. Again, a big shout out to PCBWay for providing the prototypes free of charge. Below are some of the 3D renders.

Please leave comments here on my blog or on my youtube channel if you have suggestions.

Suggested Battery Holders for The Jeffrey PCB v2.0:

Front
Back

Final Version of The Jeffrey 2.0

PLEASE NOTE: Through-hole support for the battery holder has been discontinued after receiving feedback from the community. Only surface-mounted battery holders will be supported moving forward.

Final Version has Physically Arrived 🙂


Joey Joe Joe Jr

I was born on a pirate ship off the coast of Peru where I was given a traditional Aztec upbringing, during which I excelled in the arts of sciences. At age seven my parents accidentally murdered each other in a freak fencing accident. Heartbroken I joined the tribe of Omaha, where I trained under the legendary Vin Diesel. At age eighteen, after a failed Fear Factor audition, I set out for a berry plantation roughly four kilometers south of Albuquerque. I currently reside at Ram Ranch which really rocks!

33 Comments

Nikos · February 7, 2020 at 10:53 AM

Where can i expect to buy The Jeffrey PCB ?

    Joey Joe Joe Jr · February 7, 2020 at 5:23 PM

    It will be available from PCBWay.com once I get my hands on it and do a quality check. The final prototypes were ordered a week and a half ago but the Chinese New Year Festival had caused delays. Hopefully, it will arrive soon. The PCB will be released with an assembly video.

Rod · February 8, 2020 at 6:45 AM

Will the giveaway planned for February 5th, be delayed until these new boards arrive from PCBWay.com?

    Joey Joe Joe Jr · February 8, 2020 at 1:53 PM

    I will release a video Monday announcing the winner and review the final version of The Jeffrey 2.0. Thanks for your patience.

Jeffery Schneider · February 10, 2020 at 11:44 AM

And when The Jeffrey 2.0 is available, do we buy from you? or from PCBWay?

Gonzalo · February 10, 2020 at 11:59 AM

Great work redesigning the board. It looks really nice. Will you release the design files?

Bruce · February 10, 2020 at 2:16 PM

Hi,
230K is not a Valid Resistor decade Value, The closest you will find will be the 230.7K or 232k
and that not easy, to find either , I will post some results after I dig around

    Joey Joe Joe Jr · February 10, 2020 at 2:22 PM

    Apparently, 230k is a typo in the original docs. I’m told that it should be 220k. Although it doesn’t matter too much as that resistor is used to measure the battery voltage and that reading can be calibrated via a factor inside the iSpindel configuration menu. Therefore, 220k or 230k or something close will work fine 🙂

Marcelo · February 11, 2020 at 1:38 AM

Can’t wait for the The Jeffrey PCB 2.0. CHeers.

jimdkc · February 11, 2020 at 11:11 PM

I’ve got parts on order… Can’t wait to order some boards!

Rod · February 19, 2020 at 9:55 AM

I ordered 5 yesterday. Can you share some new videos of setting up the latest version through actual gravity readings?

    Joey Joe Joe Jr · February 19, 2020 at 10:12 AM

    Hey Rob, thanks for your order. I will be working on a video series showing assembly and all the calibrations and linking it to data services. I’m currently away on business this week then away on vacation next week. The assembly for this board will be pretty close to the CherryPhilips version (link below), except there will be the tabs to file down to fit it snuggly into the pelting. Install the battery in the lowest position as the one I built floated at 25.XX degrees in pure water without the need to add external weights which was a pleasant surprise. You can use a 220k resistor as 230k isn’t needed, either or will work though. New assembly video will follow when I return. Let me know if you need any assistance along the way.

    Cheers,

    Joey Joe Joe Jr.

    https://www.opensourcedistilling.com/ispindel-assembly/

brouwkip · February 22, 2020 at 1:42 PM

I am about to order 5 of the ver2 boards but looking at your video it seems that the diode on the D1 was not removed.
do you or do you not have to remove the diode on the D1

    Joey Joe Joe Jr · February 24, 2020 at 5:14 PM

    Yes, remove the diode. Removing it is a safety feature. Pelting dimensions are.

    Parameters:
    Color Clear, gently grey
    Dimensions (external, MAX), mm ~135 x (d39, d43 MAX)
    Dimensions (internal), mm
    ~123 x d33
    Conversion: 1mm = 0.0393 inch, or 1 inch = 25.4mm

Eric · February 23, 2020 at 1:13 PM

I am about to order 5 spindel pcb’s and build them according to your instructions only on the video it does not seem you have removed the diode from the D1 is this still required? Also can you give me the dimensions of the petling, it is not always possible to order from amazon in The Netherlands.

Cheers,
Eric

    Joey Joe Joe Jr · February 24, 2020 at 5:13 PM

    Yes, remove the diode. Removing it is a safety feature. Pelting dimensions are.

    Parameters:
    Color Clear, gently grey
    Dimensions (external, MAX), mm ~135 x (d39, d43 MAX)
    Dimensions (internal), mm
    ~123 x d33
    Conversion: 1mm = 0.0393 inch, or 1 inch = 25.4mm

Eric · February 26, 2020 at 4:16 AM

Thanx

    Joey Joe Joe Jr · March 3, 2020 at 12:05 PM

    No prob. Those pelting specs are from the ebay page I link to. They should deliver worldwide.

Sergey · March 3, 2020 at 11:45 AM

Hello! Cool design, good work. I ordered 10 boards. Just do not understand how the battery holder is attached. Will the holders with pins fit?

    Joey Joe Joe Jr · March 3, 2020 at 12:03 PM

    No pins, they are surface mounted like these ones.

    An assembly vid will be coming out soon. Just got back from 2 weeks of being out of town. You just tin the contacts on the battery holder and tin the pads on the PCB. Put in position then apply heat, they will fuse together. This config makes it easy to move the battery holder later if need be. Also, these battery holders tend to be cheaper.

Nikos · March 3, 2020 at 12:01 PM

When can we expect your construction video for the board ?

    Joey Joe Joe Jr · March 3, 2020 at 12:08 PM

    It’s in the editing room now. Hopefully in the next week. Time is a little tight right now as I just got back into town after being away for 2 weeks.

Eric · March 3, 2020 at 12:27 PM

Beautiful, I’ve ordered the boards and the rest of the supplies and they will not arrive within a month

jimdkc · March 4, 2020 at 5:19 PM

I have my boards and all of my parts except for the battery holders. Looking forward to the adventure to come!

Leave a Reply

Your email address will not be published. Required fields are marked *